Confirm the angle and radius
State the angle and centre-line radius with units. If using an R:D ratio, define D and give the required radius on the drawing.
LEKE PIPING / PRODUCTS
Pipe Elbows & Bends
Elbows and bends change piping direction. Specify angle, centre-line radius and end dimensions; include tangent lengths for bends.
PRODUCT DETAILS
Specify the connection completely.
We can also make custom sizes, wall thicknesses and other dimensions to your drawing. Send the pipe-end requirements and your drawing with your RFQ so we can confirm the details.
| Parameter | Details to confirm |
|---|---|
| Type | Elbow or bend; standard or drawing-based geometry |
| Geometry | Angle and centre-line radius with units; define D when specifying an R:D ratio |
| Ends | Outside diameter, wall thickness, end preparation and straight tangent length at each end |
| Reference | ASME B16.9 / B16.28 where applicable, or the project drawing |
Product dimensions, material grades and documentation are confirmed against your enquiry and applicable project requirements.
Primary dimensional reference: ASME B16.9 (overall scope NPS 1/2–48) for covered elbows; project drawing for other bends. Confirm the product type, edition and applicable size before order.
DIMENSIONAL REFERENCE
Pipe Elbow & Bend dimensional drawing.
Use the section view to identify the dimensions to confirm in your enquiry.
Views shown separately for legibility. The full original drawing remains available below.
View full-size drawing ↗Reading this drawing
- D
- End outside diameter
- t
- Wall thickness
- A
- 90° centre-to-end dimension
- B
- 45° centre-to-end dimension
- K
- 180° return back-to-face dimension
- O
- 180° return centre-to-centre dimension
Symbols describe this supplied drawing. Confirm their correspondence with the selected standard and dimension table; notation may differ.
Illustrative geometry only. Confirm size, wall thickness, dimensions, tolerances and the applicable standard edition in the selected table or approved drawing.
SELECTION & ENQUIRY
The details that make the difference.
Define both ends
Specify the outside diameter, wall thickness and welding-end preparation at both ends. Give each straight tangent length separately where required.
Send special geometry
For non-standard bends, provide the drawing number and revision, orientation, critical dimensions and tolerances, plus inspection requirements.
TECHNICAL REFERENCES
Check dimensions before your RFQ.
ASME B16.9 / B16.28
Butt-weld fitting dimensions and geometry
Check the stated edition, units and scope. The confirmed project specification governs final requirements.
Pipe Elbows & Bends — weight estimate
Use the existing calculator for preliminary estimates. Confirm the final dimensions, material and actual product weight separately.
PRODUCT VIEWS
Pipe elbows and bends — closer look.
Compare the product views. Use the dimensional drawings and confirmed specifications for your order.
DIMENSIONAL REFERENCES
Product reference dimensions.
Reference data retained from the existing product page. Check the stated standard, edition, units and the approved project specification.
Open dimensional reference tables
Product overview
Two ways to change the direction of a pipe run.
Pipe elbows are fittings used for a directional change and are commonly specified by nominal size, schedule, radius, material and fitting standard. Pipe bends are formed sections of pipe, often made to a project-specific radius, angle and tangent length.
Before quotation, provide the available drawing, pipe size, wall thickness, material, standard, angle, radius, quantity, destination and any documentation requirements.
Explore Butt Weld FittingsProduct scope
| Pipe elbows | Butt-welding elbows for defined angles and radii, subject to requirement |
|---|---|
| Pipe bends | Formed bends specified by project geometry and manufacturing requirements |
| Angles & radius | 45°, 90°, 180°, long radius, short radius or stated project dimensions |
| Materials | Carbon steel, stainless steel and alloy steel |
| Standards | ASME B16.9, ASME B16.28 and other stated project standards |
Final suitability, dimensions, manufacturing method and documentation remain subject to the confirmed product and project requirements.
COMMON QUESTIONS
Before you send the enquiry.
What should I specify for a non-standard bend?
Include angle, centre-line radius, pipe outside diameter, wall requirements and any straight tangents. A drawing helps define the complete geometry.
Which angle and radius details should I state?
State the bend angle and required centreline radius, together with pipe diameter and wall thickness. Attach a drawing where orientation or end-to-end dimensions matter.
Can two elbows of the same nominal size have different dimensions?
Yes. Angle, radius and governing dimensional requirements can differ. Check the required centre-to-end dimensions rather than selecting by nominal size alone.
How should multiple pipe bends be identified in one order?
Give each bend a unique item number and drawing revision. List its angle, radius, tangent lengths, pipe dimensions and material on the same line so that similar bends are not confused.
Should I specify end preparation?
Yes. Identify the required connection and welding-end preparation from the approved project documents. A catalogue image does not define the supplied end geometry.
Related products
Equal & Reducing Pipe TeesReview the run and branch sizes for your enquiry.
View product details →
Concentric & Eccentric Pipe ReducersReview both end sizes and the required configuration.
View product details →
Butt Weld Pipe CapsReview the end size, wall and closure dimensions.
View product details →Need Pipe Elbows & Bends?
Request a quote for this product →Send the angle, centre-line radius, end sizes, wall thickness, material grade and quantity. Include the standard edition, drawing revision and required inspection documents.
SEND YOUR REQUIREMENT
From your specification
to a clearer quotation.
Email an itemized elbow or bend list with drawing revisions, quantities, destination and required date.
USEFUL TO INCLUDE
- Angle and centre-line radius
- Nominal size / outside diameter and wall thickness
- Material, standard and end details
- Quantity, drawings and inspection requirements
The quotation will confirm supply scope, required documents and delivery terms.